3 small woodworking projects that are easy to build, inexpensive to make, and designed around products people actually buy and display. In this video, I’m building a hat display, a vinyl record holder, and a simple cedar glasses holder — all beginner-friendly woodworking projects with great selling potential.
The craziest one might be the glasses holder. I made it from a standard 6-foot cedar fence picket, and because each one is only about 10 inches long, I can get roughly 35 glasses holders from a single picket. At just $10 each, that’s up to $350 worth of product from one inexpensive piece of cedar. Similar handmade glasses holders are selling for even more online.
The other two projects are made from pine: a simple hat holder/display and a vinyl record display shelf. All three are small woodworking projects that don’t require a lot of lumber, complicated joinery, or expensive materials, which makes them great ideas for anyone selling woodworking projects on Etsy, at craft fairs, Facebook Marketplace, or through a small woodworking business.
If you’re looking for woodworking projects that sell, easy woodworking projects for beginners, profitable woodworking ideas, small wood projects, Etsy woodworking ideas, craft fair projects, woodworking side hustle ideas, fence picket projects, scrap wood projects, hat displays, record holders, or glasses holders, hopefully this video gives you a few ideas you can put to work in your own shop.
Let me know in the comments which of the three you would build — and which one you think would sell the fastest.
Now let’s get to building.
#Woodworking #WoodworkingProjects #WoodworkingThatSells #BeginnerWoodworking #EtsySeller #WoodworkingBusiness #DIYWoodworking #CraftFairIdeas #SmallWoodProjects #lowespartner
Here’s some affiliate links to some of the stuff i used in this video. i get a few cents for snack 🍪🍫money if you use my links so Thank you if you do!! 🙏
4″ Hole Saw –
Dovetail Router Bit –
Router Table –
Key Hole Slot Router Bit –
1/2 Inch Straight Bit –
Workpro Clamps –
12” Woodworking Square Ruler –
EVA Featherboard –
Safety Glasses –
Finger Sander –
_____________________________________
00:00 Best selling Builds Intro
00:36 Cutting The wood
01:14 Circle Cutting Jig
02:44 Cut a wood circle
04:15 How To Find the Center of a Circle
06:24 How To Rout A Circle edge
09:05 Drill Dowl Holes
09:55 Project Glue Up
10:23 Make $150 From A 1×2
10:58 How to use a Featherboard
11:58 Cutting the Angle with a router
12:23 How to make a keyhole slot
14:04 Keyhole slot alternative
15:27 Water Based Clearcoat
15:40 Diy Hat Display Holder
16:41 Etsy woodworking Profits
17:20 DIY Wood Vinyl Record Holder
17:44 Does Woodworking Sell
18:57 Make Money From 1 Picket
19:55 How to Mortis The Groove
22:30 DIY Wood Glasses Holder
22:58 Can you Make Money on Etsy
source
Here's some affiliate links to some of the stuff i used in this video. i get a few cents for snack 🍪🍫money if you use my links so Thank you if you do!! 🙏
4" Hole Saw – https://link.amazon/B01xKnvIN
Dovetail Router Bit – https://link.amazon/B0gKwwITA
Router Table – https://link.amazon/B08CLWCgQ
Key Hole Slot Router Bit – https://link.amazon/B01DckbfV
1/2 Inch Straight Bit – https://link.amazon/B02LNuj4G
Workpro Clamps – https://www.amazon.com/dp/B0875WV3CD?ref=t_ac_spc_accepted_tile&linkCode=tr1&tag=jascogoods-20&linkId=B0875WV3CD_1789669796396
12” Woodworking Square Ruler – https://www.amazon.com/dp/B0CJF4YFR6?ref=t_ac_spc_accepted_tile&linkCode=tr1&tag=jascogoods-20&linkId=B0CJF4YFR6_1789669820305
EVA Featherboard – https://link.amazon/B0hfGm5ST
Safety Glasses – https://www.amazon.com/dp/B07GB8Y11G?ref=t_ac_spc_accepted_tile&linkCode=tr1&tag=jascogoods-20&linkId=B07GB8Y11G_1789668468899
Finger Sander – https://www.amazon.com/dp/B09PMZG3ZS?ref=t_ac_spc_accepted_tile&linkCode=tr1&tag=jascogoods-20&linkId=B09PMZG3ZS_1789668514115
The amount in the carts is not real. As soon as my wife setup her Etsy account and didn't even pist an item for sale yet it said in 8 carts instantly .
Great Video…!!! FYI…at 6:24 you called yourself an "Idiot"…lol
Hanging something flush to the wall…what about the "3M Claw" type hardware?
just weird and he made alot ot of mistakes
5:44 "Boom!" is 100% necessary.
Love this guy!!! Had me laughing so hard
bc Milwaukee drill chucks suck, Chuck!!
I watched your video, great projects & best sense of humor 😂
I enjoyed this video. Was entertaining, informative and the occasional flatulent noises added a new angle to the wood working experience! Cheers from Norway.
Would be a better video if you weren’t trying to be funny and it’s to long I lost interest after 12 minutes I still don’t know what you’re making.
what's wrong with a 3 minute video????? most you tubers are to long winded, talk talk never get to the point! thanks for the how to hurt your self lesson!
Your hat stand isn't likely to sell in the UK because we really don't bother with hats. Maybe a baseball hat, but they are just thrown over a coat hooks or dumped on a table. Glasses holder, may sell. The simple picture prop would likely sell.
You can rip the horizontal boards about enough for 3 or 4 whatever sozed dows to be glued into the smaller side if the ripped peice of shelf, then perfectly match up the other side abs drill holes fornthe dows to slide onto, pit small lock screws on bottom chamfered for taking off again
If your drill chuck is worn out, you can buy a replacement. Keep in mind it might be left-hand thread
I'm not shocked at all! These are so useful and they look amazing, of course they sell fast! Great idea turning scrap into something people actually want to buy.
Quick tip. Most drills have a bit lock, tighten your bit then turn back until you hear 1 click, now its locked and your bit wont keep falling out. Like i say, MOST drillshave this function, not ALL.
Could you hang the piece on the wall with a French cleat?
I use sandpaper wrapped around a paint stick.
Ive been practicing farting the entire alfmphabet
You showed how to cut the circle with the guide bit. Great. We all can do that. How do you cut a perfect circle if you don't have the guide bit? You need to cut the perfect circle to make a guide. If i don't have a guide bit i am back to bouncing around to make a jig.
Ya your( fart )got you a thumbs down .Your not the only one watching your videos. Sometimes children with some education like some of them yander shows .With all respect don't act like an idiot Boludo
The hole saw comes out because Milwaukee drill chucks are complete trash
я не зял бы такую херню даже если бы мн доплатили…
Мне это нужно чтобы поставить фото.👍
The common theme is "will only sell in us".
I love the channel brother, very informative and just fun.
My channel was just for fun, but Now I'm finally starting to get Motivated and I'm having Fun!!! 😁⚒️💚
Ken needs to make more appearances.
That hat holder as a wall mount be cool too
BUH-DURRRRRRRR
Hahahaha 😂 this guy is 😂😂hilarious
Use a drill press with the hole saw without the bit.
I've never once thought to take the battery out of my router when charging bits…
…but i do always unplug it.
~boB
Excelente maestro
Saludos desde Chile……🇨🇱🇨🇱🇨🇱🇨🇱
It was Grandma Vivienne for me: partly because she could have stepped straight out of "The Devil Wears Prada"; but, my Great Aunt Belle-Belle was exactly like her. Great, but not to be messed with!
What is that noise you make? Do you have Tourette’s Syndrome, do you?
Jasco; you are an absolute hoot to watch, and I think a pretty fine woodworker too if you didn't have to fart around with all the camera and audio takes and editing. I can always fined good ideas and some good laughs watching your videos. Keep rolling the cameras! 🤗😅 🤣
I have seen most of your videos and they are awesome. I love the mistakes you make and you're right about this is how you learn.
I wonder if you can make a vibrating table that is 12"x9" working area. Hopefully not too expensive.
As soon as I saw you pushing down on the hole saw, I knew…
I love your style! Do you hsve a video that recommends what tools to accuire maybe on a must haves, next up, and dream tools order? I'm not sure what to go for. If i had a shopping list I could pick them up as they show up at Lidl.
it's a lot easier than that to find center. Any 90° triangle imposed inside the circle has a hypotenuse that IS a diametric line. Lay your square down, put the 90° outside corner on the circumference, draw lines down the legs, and connect the ends. One step instead of two [roughtly the 5:30 – 6:00 minute portion of the video.]
Nice projects…..but……you sure could save a lot of dinking around with hole saws and jigs if you got yourself a small CNC machine! Most could be programed for one pass with just a few bit changes. Lordy!
You didn’t lock you drill chuck!
I love your mistakes and your fart humor the most. I have no interest in selling stuff but the tips are nice!